ut6 Posted November 13, 2012 Share Posted November 13, 2012 (edited) Anybody with LEDs, what kind of wattage do you run and what kinds of corals do you have under yours? Looking to buy some LEDs but not sure what I want to go with. Edited November 13, 2012 by ut6 Quote Link to comment Share on other sites More sharing options...
ckyuv Posted November 13, 2012 Share Posted November 13, 2012 you lookin to do a diy or lookin for a manufactured set up? i won rapid led kit at arc meeting and they were awesome i now have kessil 350w and plan to keep it till it dies. I have mainly sps Quote Link to comment Share on other sites More sharing options...
ut6 Posted November 13, 2012 Author Share Posted November 13, 2012 Probably a manufactured set up.. Quote Link to comment Share on other sites More sharing options...
Juiceman Posted November 13, 2012 Share Posted November 13, 2012 I have 3 EVO150's at 150w a piece over 7 feet of tank. I have everything coral wise. Quote Link to comment Share on other sites More sharing options...
ut6 Posted November 13, 2012 Author Share Posted November 13, 2012 At the moment I have about 95% lps but I plan to add more sps over time and want to know what you guys think is a sufficient amount of lighting for sps growth. Quote Link to comment Share on other sites More sharing options...
+Capt. Obvious Posted November 13, 2012 Share Posted November 13, 2012 I ran a Kessil A150 for a while, great light for smaller tanks, the A350 is a great light as well. I currently run AI SOL Super Blues and will be adding a Vega soon. here is a snippet of info about wattage and LEDs: A COMMON MISCONCEPTION WITHIN THE INDUSTRY IS THAT 3W LED CONSUMES 3W OF POWER, 10W = 10W ETC. A WATT IS A WATT RIGHT? This misnomer comes from the early days of LEDs, which is a legacy of traditional lighting sources. A 54W T5 uses around 54W, and a 250W metal halide uses around 250W. (both actual values are dependent on the ballast) A Cree XP-G emitter may be driven at approximately 5W. This value is calculated by 1.5 amps multiplied by a forward voltage of 3.3V. Now, just because it can be driven at 5W doesn't mean there is benefit in doing so. As the LED is driven at higher power levels, the temperature of the device increases and its luminous efficacy is decreased. What this means is that one LED system may be driven at 5W per XP-G achieving 63 lumens per watt while another LED system drives the same XP-G at 2.5W and achieves 84 lumens per watt. This is over a 25% difference in system efficacy! In this example, the XP-G LED driven at 5W is outputting twice the light as the 2.5W, but in doing so runs at a higher temperature (decreasing lifespan) and operates at 25% less system efficacy. On the same line of discussion, many manufacturers advertise their LED system in a rather misleading manner, in two ways. Example: Brand X has 110W of LED per foot of fixture. Does this mean that if you measure power consumption, from the wall, it consumes 110W per foot? The manufacturer is stating they use 10 Cree XP-E Blue at 3W, 10 Cree XP-E Royal Blue at 3W, 10 XP-G Cool White at 5W equaling 110W. Does this mean that all of the LEDs are ran at maximum power? The AI Sol, and all of our products stating the power consumption from the wall. The AI Sol Blue (and White) uses 74-75W depending on the power meter used and temperature of the room. If you break this down, it consists of each of the Cree XP-E Royal Blue and Blue emitters run around 2.6W and the Cree XP-G Cool White runs at just under 2.5W. The control circuitry, fan, and power supply inefficiency brings the total power consumption to 74-75W. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.